华为MA5620、MA5626 ONU改交换机详细配置
一、串口参数设置
串口参数如图所示：波特率9600bit/s、8位数据位、1位停止位、无校验和无流控。
二、设备进入配置视图并重置设备配置
username：rootpassword:mduadmin#输入密码的时候不显示内容，输入完按回车即可ma5626>enable#进入用户视图ma5626#config#进入配置视图，下面参数配置都在该视图下ma5626(config)#erase flash data#回车后选择y，然后重启设备输入ma5626(config)reboot system#输入y确定重启即可，重启后里面的数据会被清空，恢复到出厂默认配置。
三、MA5620设备配置
MA5626(config)##配置需要在config视图下配置vlan 1 smart#创建VLANvlan service-profile profile-id 1#创建服务模板vlan bind service-profile 1 profile-id 1#绑定服务模板service-port vlan 1 eth 0/1/1 multi-service user-vlan untagged rx-cttr 6 tx-cttr 6 service-port vlan 1 eth 0/1/2 multi-service user-vlan untagged rx-cttr 6 tx-cttr 6 service-port vlan 1 eth 0/1/3 multi-service user-vlan untagged rx-cttr 6 tx-cttr 6 service-port vlan 1 eth 0/1/4 multi-service user-vlan untagged rx-cttr 6 tx-cttr 6 service-port vlan 1 eth 0/1/5 multi-service user-vlan untagged rx-cttr 6 tx-cttr 6 service-port vlan 1 eth 0/1/6 multi-service user-vlan untagged rx-cttr 6 tx-cttr 6 service-port vlan 1 eth 0/1/7 multi-service user-vlan untagged rx-cttr 6 tx-cttr 6 service-port vlan 1 eth 0/1/8 multi-service user-vlan untagged rx-cttr 6 tx-cttr 6 service-port vlan 1 eth 0/1/9 multi-service user-vlan untagged rx-cttr 6 tx-cttr 6 service-port vlan 1 eth 0/1/10 multi-service user-vlan untagged rx-cttr 6 tx-cttr 6 service-port vlan 1 eth 0/1/11 multi-service user-vlan untagged rx-cttr 6 tx-cttr 6service-port vlan 1 eth 0/1/12 multi-service user-vlan untagged rx-cttr 6 tx-cttr 6service-port vlan 1 eth 0/1/13 multi-service user-vlan untagged rx-cttr 6 tx-cttr 6 service-port vlan 1 eth 0/1/14 multi-service user-vlan untagged rx-cttr 6 tx-cttr 6 service-port vlan 1 eth 0/1/15 multi-service user-vlan untagged rx-cttr 6 tx-cttr 6service-port vlan 1 eth 0/1/16 multi-service user-vlan untagged rx-cttr 6 tx-cttr 6service-port vlan 1 eth 0/1/17 multi-service user-vlan untagged rx-cttr 6 tx-cttr 6 service-port vlan 1 eth 0/1/18 multi-service user-vlan untagged rx-cttr 6 tx-cttr 6 service-port vlan 1 eth 0/1/19 multi-service user-vlan untagged rx-cttr 6 tx-cttr 6 service-port vlan 1 eth 0/1/20 multi-service user-vlan untagged rx-cttr 6 tx-cttr 6 service-port vlan 1 eth 0/1/21 multi-service user-vlan untagged rx-cttr 6 tx-cttr 6 service-port vlan 1 eth 0/1/22 multi-service user-vlan untagged rx-cttr 6 tx-cttr 6 service-port vlan 1 eth 0/1/23 multi-service user-vlan untagged rx-cttr 6 tx-cttr 6 service-port vlan 1 eth 0/1/24 multi-service user-vlan untagged rx-cttr 6 tx-cttr 6 #端口绑定vlan并剥离标签undo isolate port 0/1/1undo isolate port 0/1/2undo isolate port 0/1/3undo isolate port 0/1/4undo isolate port 0/1/5undo isolate port 0/1/6undo isolate port 0/1/7undo isolate port 0/1/8undo isolate port 0/1/9undo isolate port 0/1/10undo isolate port 0/1/11undo isolate port 0/1/12undo isolate port 0/1/13undo isolate port 0/1/14undo isolate port 0/1/15undo isolate port 0/1/16undo isolate port 0/1/17undo isolate port 0/1/18undo isolate port 0/1/19undo isolate port 0/1/20undo isolate port 0/1/21undo isolate port 0/1/22undo isolate port 0/1/23undo isolate port 0/1/24#取消端口用户隔离，新设备不需要配置该命令V800R308产品分为新老架构，新架构是指采用SD5103芯片的设备port mode 0/0/1 ge port mode 0/0/2 ge #指定1，2光口为GE模式。然后把业务口透传到光口，port vlan 1 0/0 1 #以太网口 vlan1 透传到上行口1port vlan 1 0/0 2 #以太网口 vlan1 透传到上行口2#配置光口上联save#保存配置
四、MA5626设备配置
MA5626(config)##配置需要在config视图下配置VLAN 1 smart#创建VLANvlan service-profile profile-id 1user-bridging enable#服务模板下开启用户互通commitquitvlan bind service-profile 1 profile-id 1#vlan与服务模板绑定service-port vlan 1 eth 0/1/1 multi-service user-vlan untagged rx-cttr 6 tx-cttr 6 service-port vlan 1 eth 0/1/2 multi-service user-vlan untagged rx-cttr 6 tx-cttr 6 service-port vlan 1 eth 0/1/3 multi-service user-vlan untagged rx-cttr 6 tx-cttr 6 service-port vlan 1 eth 0/1/4 multi-service user-vlan untagged rx-cttr 6 tx-cttr 6 service-port vlan 1 eth 0/1/5 multi-service user-vlan untagged rx-cttr 6 tx-cttr 6 service-port vlan 1 eth 0/1/6 multi-service user-vlan untagged rx-cttr 6 tx-cttr 6 service-port vlan 1 eth 0/1/7 multi-service user-vlan untagged rx-cttr 6 tx-cttr 6 service-port vlan 1 eth 0/1/8 multi-service user-vlan untagged rx-cttr 6 tx-cttr 6 service-port vlan 1 eth 0/1/9 multi-service user-vlan untagged rx-cttr 6 tx-cttr 6 service-port vlan 1 eth 0/1/10 multi-service user-vlan untagged rx-cttr 6 tx-cttr 6 service-port vlan 1 eth 0/1/11 multi-service user-vlan untagged rx-cttr 6 tx-cttr 6service-port vlan 1 eth 0/1/12 multi-service user-vlan untagged rx-cttr 6 tx-cttr 6service-port vlan 1 eth 0/1/13 multi-service user-vlan untagged rx-cttr 6 tx-cttr 6 service-port vlan 1 eth 0/1/14 multi-service user-vlan untagged rx-cttr 6 tx-cttr 6 service-port vlan 1 eth 0/1/15 multi-service user-vlan untagged rx-cttr 6 tx-cttr 6service-port vlan 1 eth 0/1/16 multi-service user-vlan untagged rx-cttr 6 tx-cttr 6service-port vlan 1 eth 0/1/17 multi-service user-vlan untagged rx-cttr 6 tx-cttr 6 service-port vlan 1 eth 0/1/18 multi-service user-vlan untagged rx-cttr 6 tx-cttr 6 service-port vlan 1 eth 0/1/19 multi-service user-vlan untagged rx-cttr 6 tx-cttr 6 service-port vlan 1 eth 0/1/20 multi-service user-vlan untagged rx-cttr 6 tx-cttr 6 service-port vlan 1 eth 0/1/21 multi-service user-vlan untagged rx-cttr 6 tx-cttr 6 service-port vlan 1 eth 0/1/22 multi-service user-vlan untagged rx-cttr 6 tx-cttr 6 service-port vlan 1 eth 0/1/23 multi-service user-vlan untagged rx-cttr 6 tx-cttr 6 service-port vlan 1 eth 0/1/24 multi-service user-vlan untagged rx-cttr 6 tx-cttr 6 #端口绑定vlan并剥离标签port mode 0/0/1 ge port mode 0/0/2 ge #指定1，2光口为GE模式。然后把业务口透传到光口，port vlan 1 0/0 1 #以太网口 vlan1 透传到上行口1port vlan 1 0/0 2 #以太网口 vlan1 透传到上行口2#配置光口上联save#保存配置
五、开启POE设备供电
MA5626(config)#interface eth 0/1poe power-management autopoe temperature-protection#开启设备自动POE供电功能port 1 enable mode signal priority critical max-power 30000port 2 enable mode signal priority critical max-power 30000port 3 enable mode signal priority critical max-power 30000port 4 enable mode signal priority critical max-power 30000port 5 enable mode signal priority critical max-power 30000port 6 enable mode signal priority critical max-power 30000port 7 enable mode signal priority critical max-power 30000port 8 enable mode signal priority critical max-power 30000#开启端口最大供电功率30W,避免因为供电设备没办法启动
开光口级联：
root
密码mduadmin
（这是默认的用户名和密码）
登陆onu后输入的命令：
enable —回车
erase flash data —回车
Y —回车
reboot system—回车
Y—回车
回车后等待片刻onu重启后以前所配置的数据即可全部删除
MA5626>
enable
config
port mode 0/0/1 ge
port mode 0/0/2 ge 指定1，2光口为GE模式。然后把业务口透传到光口，真要命，找好久还搞明白。
vlan service-profile profile-id 1
user-bridging enable 用户桥接使能
commit 加载
quit
vlan 4000 smart 定义管理vlan
vlan bind service-profile 4000 profile-id 1 将vlan邦定1号模板
multi-service-port vlan 4000 port 0/1 1-8 user-vlan untagged rx-cttr 6 tx-cttr 6 批量加载业务口
interface vlanif4000 进入管理vlan
ip address 111.111.111.1 255.255.255.0 带内管理ip地址
quit
port vlan 4000 0/0 1 ETH口 vlan1 透传到上行口1
port vlan 4000 0/0 2 ETH口 vlan1 透传到上行口2
save
reboot system
MA5626(config)#undo service-port all
MA5626(config)#interface eth 0/1
MA5626(config-if-eth-0/1)#traffic-suppress all unicast value 1
MA5626(config-if-eth-0/1)#traffic-suppress all broadcast value 1
MA5626(config-if-eth-0/1)#quit
MA5626(config)#multi-service-port vlan transparent board 1 other-all rx-cttr 6 tx-cttr 6
确实要批量增加业务虚端口? (y/n)[n]:y
本次批增操作涉及业务单板总数: 1
本次批增操作涉及业务虚端口总数: 24
批量增加开始…
批量增加结束:
本次批增需要增加业务虚端口总数: 24
其中, 增加成功总数: 24
MA5626(config)#save data
设备图片:
配置华为MA5626恢复出厂设置，包括登陆密码，还原后默认信息：
用户名：root
密码:mduadmin
一、准备工作
准备工作：console线、超级终端、华为MA5626_ONU空库文件、华为MA5620_ONU空库文件。
1、通过上面的链接下对应软件。
2、准备一条Console线，DB9转RG45,如下图(如果有这种线可以找一台旧台式机，插到主机后面连到华为的Consoel口中：
3、如果你只有笔记本，而笔记本不带COM口可以选购下面这种线：
二、连接配置设备
1、打开超级终端软件，点击新建，配置参数如下图：
2、具体配置请参考下面文本信息：
Platform System start ... //设备启动
Memory Data Bus Test .................pass.
Memory Address Bus Test .................pass.
Press 'Ctrl+T' To Start Memory Complete Test
Trace code : 0x10047200
Copy from ROM to RAM ...... OK!
Uncompress from ROM to RAM ...... OK!
System Vfs init...OK
The latest reboot is caused by : others
Copyright (c) 1998 - 2011 by Huawei Technologies Co.,Ltd.
All Rights Reserved.
The last update date of base BIOS B is : Jan 4 2011 09:43:09
===============================================================
BOARD INFORMATION :
CPU: ARM Integrator - ARM1176JF (ARM). Processor running at 533Mhz
256M bytes DDRAM, 64M bytes flash memory installed on board
Baudrate of serial channel is 9600bps
Board's LAN IP address is 10.11.104.2
Board's LAN Subnet mask is 255.255.255.0
Board's LAN MAC address is 78:1D:BA:F6:90:20
===============================================================
System is booting from base BIOS...
Base BIOS version is 200
Press <D> key to stop auto-boot 1 //到这里按“d”键中断启动
Main menu:
==============================================
0 Boot from flash
1 Load files
9 Reboot system
Please enter a choice : 1 //选择1 Load files
SubMenu: Load files
==============================================
0 Back to main menu
1 Download program file to flash
2 Download Data file to flash
3 Download basebios file to flash
4 Download cpld file
5 Download packet file
d Download program file to ddram
6 Download updatetool file to flash
7 Download equipment file to flash
Please enter a choice : 2 //选择2 Download Data file to flash配置库文件
Please select load mode[default: 1 -- TFTP load mode]:
============================================
0 Xmodem load mode
1 TFTP load mode
Q Quit
Please enter your choice:0 //选择0. 使用串口传输
Please Select download speed:
1. 9600BPS
2. 19200BPS
3. 38400BPS
4. 57600BPS
5. 115200BPS
Select baudrate[default : 1]: 1 //选择1. 9600BPS 波特率为9600
You will download file by xmodem at 9600 BPS, are you sure? (y/n) [y]y //按y 确认
Please change baudrate to 9600 BPS and press enter key //按回车键（Enter）进行下一步
Press CTRL+C key to abort!
Waiting ...CCCCCCC //这个时候需要看看第二步过程3 在软件上选择发送文件，协议为“xmodem”
Download Success! 44658 bytes download OK
save file to main area.....ok!
save file to spare area.....ok!
SubMenu: Load files
==========================================//至此库文件就恢复完成，后续步骤，重启
0 Back to main menu
1 Download program file to flash
2 Download Data file to flash
3 Download basebios file to flash
4 Download cpld file
5 Download packet file
d Download program file to ddram
6 Download updatetool file to flash
7 Download equipment file to flash
Please enter a choice : 0 //按0 返回上一步
Main menu:
==============================================
0 Boot from flash
1 Load files
9 Reboot system
Please enter a choice : 9 //按9重启设备。
Platform System start ...
Memory Data Bus Test .................pass.
Memory Address Bus Test .................pass.
Press 'Ctrl+T' To Start Memory Complete Test
Trace code : 0x11020A02
Copy from ROM to RAM ...... OK!
Uncompress from ROM to RAM ...... OK!
System Vfs init...OK
The latest reboot is caused by : others
Copyright (c) 1998 - 2011 by Huawei Technologies Co.,Ltd.
All Rights Reserved.
The last update date of base BIOS A is : Jan 4 2011 09:43:09
===============================================================
BOARD INFORMATION :
CPU: ARM Integrator - ARM1176JF (ARM). Processor running at 533Mhz
256M bytes DDRAM, 64M bytes flash memory installed on board
Baudrate of serial channel is 9600bps
Board's LAN IP address is 10.11.104.2
Board's LAN Subnet mask is 255.255.255.0
Board's LAN MAC address is 78:1D:BA:F6:90:20
===============================================================
System is booting from base BIOS...
Base BIOS version is 200
Press <D> key to stop auto-boot 0
Now system will boot from flash memory.
Testing Flash memory...OK!
Select area information : Program Area A ,Data Area A .
Begin to expand program... OK!
Transferring control to the loaded program...OK!
Starting system application init......successfully!
Starting system configuration data init...successfully!
Error: The type of device [107] is different
from the configured type [97] in the database!
Error: Task BOX ID 1 stack overflow!
Error: Task _TIL ID 2 stack overflow!
Error: Task _EXC ID 3 stack overflow!
Error: Task VP ID 4 stack overflow!
Error: Task VIDL ID 5 stack overflow!
Error: Task TICK ID 6 stack overflow!
Error: Task ROOT ID 7 stack overflow!
Error: Task CpuBase ID 8 stack overflow!
Error: Task DBWR ID 9 stack overflow!
Error: Task DBWS ID 10 stack overflow!
Error: Task EMUR ID 11 stack overflow!
Error: Task RSA ID 12 stack overflow!
Error: Task _MfMON ID 13 stack overflow!
Error: Task _EfMON ID 14 stack overflow!
Error: Task _MfBCLI ID 15 stack overflow!
Error: Task _S0fBCLI ID 16 stack overflow!
Error: Task _S1fBCLI ID 17 stack overflow!
Error: Task _MfDIAG ID 18 stack overflow!
Error: Task _EfDIAG ID 19 stack overflow!
Error: Task _MfPHY ID 20 stack overflow!
Error: Task _MfDB ID 21 stack overflow!
Error: Task _MfDCM ID 22 stack overflow!
Error: Task _MfDEV ID 23 stack overflow!
Error: Task _MfPM ID 24 stack overflow!
Error: Task _MfALM ID 25 stack overflow!
Error: Task _MfINFC ID 26 stack overflow!
Error: Task _MfSNMP ID 27 stack overflow!
Error: Task _S0fSNMP ID 28 stack overflow!
Error: Task _MfPAT ID 29 stack overflow!
Error: Task _MfDBG ID 30 stack overflow!
Error: Task _S0fDBG ID 31 stack overflow!
Error: Task _S1fDBG ID 32 stack overflow!
Error: Task _MfLOAD ID 33 stack overflow!
Error: Task _MfBAK1 ID 34 stack overflow!
Error: Task _MfFTP ID 35 stack overflow!
Error: Task _S0fFTP ID 36 stack overflow!
Error: Task _MfLANG ID 37 stack overflow!
Error: Task _MfPER ID 38 stack overflow!
Error: Task _MfEMM ID 39 stack overflow!
Error: Task _MfL2M ID 40 stack overflow!
Error: Task _MfBTV ID 41 stack overflow!
Error: Task _MfL2P ID 42 stack overflow!
Error: Task _MAUTO ID 43 stack overflow!
Error: Task _MfL3 ID 44 stack overflow!
Error: Task _EfL3 ID 45 stack overflow!
Error: Task _MCICM ID 46 stack overflow!
Error: Task _METHOAM ID 47 stack overflow!
Error: Task _MfSRM ID 48 stack overflow!
Error: Task _S0fSRM ID 49 stack overflow!
Error: Task _MfCFGR ID 50 stack overflow!
Error: Task _MfAMP ID 51 stack overflow!
Error: Task _MfBSSP ID 52 stack overflow!
Error: Task _MfSfwdDelivery ID 53 stack overflow!
Error: Task _MfNetsw ID 54 stack overflow!
Error: Task _MfMsc ID 55 stack overflow!
Error: Task _MfProduct ID 56 stack overflow!
Error: Task _MfSfwdSend ID 57 stack overflow!
Error: Task _MfPSCM ID 58 stack overflow!
Error: Task _MLICENSE ID 59 stack overflow!
Error: Task _MfLocal ID 60 stack overflow!
Error: Task _MfXPONDRV ID 61 stack overflow!
Error: Task ABAK ID 62 stack overflow!
Error: Task DUMP_AsynDumpProcTask ID 63 stack overflow!
Error: Task Co0 ID 64 stack overflow!
Error: Task vt1 ID 65 stack overflow!
Error: Task vt2 ID 66 stack overflow!
Error: Task vt3 ID 67 stack overflow!
Error: Task vt4 ID 68 stack overflow!
Error: Task vt5 ID 69 stack overflow!
Error: Task vt6 ID 70 stack overflow!
Error: Task vt7 ID 71 stack overflow!
Error: Task vt8 ID 72 stack overflow!
Error: Task OAMPDU ID 73 stack overflow!
Error: Task OAMLINK ID 74 stack overflow!
Error: Task OAMLOOPBACK ID 75 stack overflow!
Error: Task Sfd_T_RecvPkt ID 76 stack overflow!
Error: Task Sfd_T_OamAlarm ID 77 stack overflow!
Error: Task Sfd_T_Autosense ID 78 stack overflow!
Error: Task Sfd_T_Sec ID 79
Platform System start ...
Memory Data Bus Test .................pass.
Memory Address Bus Test .................pass.
Press 'Ctrl+T' To Start Memory Complete Test
Trace code : 0x11060A01
Copy from ROM to RAM ...... OK!
Uncompress from ROM to RAM ...... OK!
System Vfs init...OK
The latest reboot is caused by : others
Copyright (c) 1998 - 2011 by Huawei Technologies Co.,Ltd.
All Rights Reserved.
The last update date of base BIOS B is : Jan 4 2011 09:43:09
===============================================================
BOARD INFORMATION :
CPU: ARM Integrator - ARM1176JF (ARM). Processor running at 533Mhz
256M bytes DDRAM, 64M bytes flash memory installed on board
Baudrate of serial channel is 9600bps
Board's LAN IP address is 10.11.104.2
Board's LAN Subnet mask is 255.255.255.0
Board's LAN MAC address is 78:1D:BA:F6:90:20
===============================================================
System is booting from base BIOS...
Base BIOS version is 200
Press <D> key to stop auto-boot 0
Now system will boot from flash memory.
Testing Flash memory...OK!
Select area information : Program Area A ,Data Area A .
Begin to expand program... OK!
Transferring control to the loaded program...OK!
Starting system application init......successfully!
Starting system configuration data init...successfully!
Press any key to get started
>>User name:root
>>User password: //输入用户名“root”密码“mduadmin”进入设备
Huawei Integrated Access Software (MA5626).
Copyright(C) Huawei Technologies Co., Ltd. 2002-2010. All rights reserved.
MA5626>enable
MA5626#config
MA5626(config)#
3、选择Xmodem编码格式传输文件
华为MA5620/MA5626 ONU配置为交换机
因为ONU拿来后默认配置为网口隔离，互相不能通信，所以我们需要通过配置来取消端口隔离
用户名:root
密码：mduadmin
VLAN 100 smart //创建VLAN100vlan service-profile profile-id 1 //配置服务iduser-bridging enablecommitvlan bind service-profile 100 profile-id 1service-port vlan 100 eth 0/1/1 multi-service user-vlan untagged rx-cttr 6 tx-cttr 6 service-port vlan 100 eth 0/1/2 multi-service user-vlan untagged rx-cttr 6 tx-cttr 6 service-port vlan 100 eth 0/1/3 multi-service user-vlan untagged rx-cttr 6 tx-cttr 6 service-port vlan 100 eth 0/1/4 multi-service user-vlan untagged rx-cttr 6 tx-cttr 6 service-port vlan 100 eth 0/1/5 multi-service user-vlan untagged rx-cttr 6 tx-cttr 6 service-port vlan 100 eth 0/1/6 multi-service user-vlan untagged rx-cttr 6 tx-cttr 6 service-port vlan 100 eth 0/1/7 multi-service user-vlan untagged rx-cttr 6 tx-cttr 6 service-port vlan 100 eth 0/1/8 multi-service user-vlan untagged rx-cttr 6 tx-cttr 6 service-port vlan 100 eth 0/1/9 multi-service user-vlan untagged rx-cttr 6 tx-cttr 6 service-port vlan 100 eth 0/1/10 multi-service user-vlan untagged rx-cttr 6 tx-cttr 6 service-port vlan 100 eth 0/1/11 multi-service user-vlan untagged rx-cttr 6 tx-cttr 6service-port vlan 100 eth 0/1/12 multi-service user-vlan untagged rx-cttr 6 tx-cttr 6service-port vlan 100 eth 0/1/13 multi-service user-vlan untagged rx-cttr 6 tx-cttr 6service-port vlan 100 eth 0/1/14 multi-service user-vlan untagged rx-cttr 6 tx-cttr 6service-port vlan 100 eth 0/1/15 multi-service user-vlan untagged rx-cttr 6 tx-cttr 6service-port vlan 100 eth 0/1/16 multi-service user-vlan untagged rx-cttr 6 tx-cttr 6//对应接口绑定对应配置，来实现互通。
MA5620的版本不支持VLAN service 模板方式，可以通过关闭端口隔离方式。
使用命令：
undo isolate port 【端口号】
配置光口上行
系统视图清空设备配置
erase flash data
华为MA5626和MA5620 ONU设备配置Telnet、SSH、SNMP远程管理
1、配置管理地址
MA5626-8-POE#switch language-mode #切换语言 当前语言模式已切换到本地语种MA5626-8-POE(config)#vlan 3 smart #创建管理vlaninterface vlanif3 #配置管理VLAN_IP地址和描述description "Home_network"ip address 10.0.0.233 255.255.255.0
2、配置Telnet、SSH服务
MA5626-8-POE(config)#terminal user name #配置telnet用户，根据引导配置用户即可 请输入用户名(长度<6，15>)：linuser 请输入用户密码(长度<6，15>)： 请确认密码(长度<6，15>)： 模板名称(<=15位)[root]： 请输入用户权限：3 #选择3管理员 1、普通用户 2、操作者 3、管理者：3 请输入用户可重复登录数(0--4)：4 请输入用户的附加信息(<=30位)：Guanli_lintengfei 用户添加成功 重复该操作？ (y/n)[n]：nMA5626-8-POE(config)#ssh user linuser authentication-type password #配置用户linuser支持SSH
3、配置SNMP
MA5626-8-POE(config)#snmp-agent community write 12345678 #配置snmp写团子字为12345678
4、检查测试保存配置
MA5626-8-POE(config)#save #保存设备配置MA5626-8-POE(config)#display current-configuration #查看设备配置{ <cr>|section<K>|simple<K>||<K> }: 命令： display current-configuration [MA562XV800R308: 3600]#[global-config] <global-config> sysname MA5626-8-POE terminal user name buildrun_new_password 597362588 *[%SM<IP3YUANMUUKMEG9L`9M!* 1 2014:02:04:05:39:54 2014:02:04:05:39:54 root 2 15 "Guanli_lintengfei" trap convert event-to-alarm 0x3721000a alarm alarmlevel 0x0a11a106 warning alarm alarmlevel 0x0a11a109 warning alarm alarmlevel 0x0a310112 warning alarm alarmlevel 0x0a310142 warning#[device-config] <device-config> port port-index 0/0/1 port-type GE-PORT port port-index 0/0/2 port-type GE-PORT#[public-config] <public-config> <public-config> port mode 0/0/1 ge port mode 0/0/2 ge snmp-agent local-engineid 800007DB035C4CA9127DAF snmp-agent community write 12345678#[vlan-config] <vlan-config> vlan 3 smart vlan 5 smart port vlan 3 0/0 1 port vlan 3 0/0 2 port vlan 5 0/0 1 port vlan 5 0/0 2#[vlan-srvprof] <vlan-srvprof> vlan service-profile profile-id 3 profile-name "srvprof-3" user-bridging enable commit vlan service-profile profile-id 5 profile-name "srvprof-5" user-bridging enable commit vlan bind service-profile 3 profile-id 3 vlan bind service-profile 5 profile-id 5 vlan bind service-profile 5 profile-id 5# [eth] <eth-0/1>interface eth 0/1 port 1 enable mode signal priority critical max-power 30000 port 2 enable mode signal priority critical max-power 30000 port 3 enable mode signal priority critical max-power 30000 port 4 enable mode signal priority critical max-power 30000 port 5 enable mode signal priority critical max-power 30000 port 6 enable mode signal priority critical max-power 30000 port 7 enable mode signal priority critical max-power 30000 port 8 enable mode signal priority critical max-power 30000#[bbs-config] <bbs-config> service-port 0 vlan 5 eth 0/1/1 multi-service user-vlan untagged rx-cttr 6 tx-cttr 6 service-port 1 vlan 3 eth 0/1/2 multi-service user-vlan untagged rx-cttr 6 tx-cttr 6 service-port 2 vlan 3 eth 0/1/3 multi-service user-vlan untagged rx-cttr 6 tx-cttr 6 service-port 3 vlan 3 eth 0/1/4 multi-service user-vlan untagged rx-cttr 6 tx-cttr 6 service-port 4 vlan 3 eth 0/1/5 multi-service user-vlan untagged rx-cttr 6 tx-cttr 6 service-port 5 vlan 3 eth 0/1/6 multi-service user-vlan untagged rx-cttr 6 tx-cttr 6 service-port 6 vlan 3 eth 0/1/7 multi-service user-vlan untagged rx-cttr 6 tx-cttr 6 service-port 7 vlan 3 eth 0/1/8 multi-service user-vlan untagged rx-cttr 6 tx-cttr 6#[abs-config] <abs-config> config#[prevlanif] <prevlanif> interface vlanif3 interface vlanif5#[vlanif] <vlanif3>interface vlanif3 description "Home_network" ip address 10.0.0.233 255.255.255.0# <vlanif5> <vlanif5>interface vlanif5 description "Siwai_AP_network"#[meth] <meth0>interface meth0 ip address 10.11.104.2 255.255.255.0#[null] <null0>interface null0#[post-system] <post-system> ip route-static 0.0.0.0 0.0.0.0 10.0.0.1 ssh user 597362588 authentication-type password#return
